1. Repeater-Builder
  2. Теми

Cat200 controller and the Ci-200

 

So have a couple of these cat controllers. The 700 model and the 200 model. 
and although programming these on the air is SO much fun😩
I would rather do this per pc control. 
but there is something called the CI200 which apparently is a interface between the controller and the pc. But CAT went out business and I have NEVER seen one of these devices. Is there a way to build something to accomplish the same task to use the pc or just suck it up and program over the air. 
 

Although nothing wrong with asking here, but you may have better luck in the CAT group.

Mick - W7CAT

----- Original Message -----
From: "TheCuecat via groups.io"
To: repeater-builder@groups.io
Sent: Sunday, December 29, 2024 07:47:28 AM
Subject: [repeater-builder] Cat200 controller and the Ci-200

So have a couple of these cat controllers. The 700 model and the 200
model.
and although programming these on the air is SO much fun?
I would rather do this per pc control.
but there is something called the CI200 which apparently is a
interface between the controller and the pc. But CAT went out business and I have NEVER seen one of these devices. Is there a way to build something to accomplish the same task to use the pc or just suck it up and program over the air.




--
Untitled Document
 

The cat700 just takes a db25 cable not sure about cat200



On Sunday, December 29, 2024, 10:13 AM, Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Although nothing wrong with asking here, but you may have better luck in
the CAT group.

Mick - W7CAT

----- Original Message -----
From: "TheCuecat via groups.io"
Sent: Sunday, December 29, 2024 07:47:28 AM
Subject: [repeater-builder] Cat200 controller and the Ci-200

> So have a couple of these cat controllers. The 700 model and the 200
model.
> and although programming these on the air is SO much fun?
> I would rather do this per pc control.
> but there is something called the CI200 which apparently is a
interface between the controller and the pc. But CAT went out business
and I have NEVER seen one of these devices. Is there a way to build
something to accomplish the same task to use the pc or just suck it up
and program over the air.
>
>
>
>
>
>
--
Untitled Document
 

Check out repeaters builders .com



On Sunday, December 29, 2024, 10:13 AM, Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Although nothing wrong with asking here, but you may have better luck in
the CAT group.

Mick - W7CAT

----- Original Message -----
From: "TheCuecat via groups.io"
Sent: Sunday, December 29, 2024 07:47:28 AM
Subject: [repeater-builder] Cat200 controller and the Ci-200

> So have a couple of these cat controllers. The 700 model and the 200
model.
> and although programming these on the air is SO much fun?
> I would rather do this per pc control.
> but there is something called the CI200 which apparently is a
interface between the controller and the pc. But CAT went out business
and I have NEVER seen one of these devices. Is there a way to build
something to accomplish the same task to use the pc or just suck it up
and program over the air.
>
>
>
>
>
>
--
Untitled Document
 

The CAT-700 uses a 10 pin header.

There aren't that many things to program with a CAT-200. Won't take that long with using DTMF to program it.

Mick - W7CAT

----- Original Message -----
From: "Jack Mcelyea/n4jem via groups.io"
To:
Sent: Sunday, December 29, 2024 04:41:00 PM
Subject: Re: [repeater-builder] Cat200 controller and the Ci-200

The cat700 just takes a db25 cable not sure about cat200




On Sunday, December 29, 2024, 10:13 AM, Teton Amateur Radio Repeater
Association (TARRA) wrote:

Although nothing wrong with asking here, but you may have better luck in
the CAT group.

Mick - W7CAT

----- Original Message -----
From: "TheCuecat via groups.io"
To: repeater-builder@groups.io
Sent: Sunday, December 29, 2024 07:47:28 AM
Subject: [repeater-builder] Cat200 controller and the Ci-200

So have a couple of these cat controllers. The 700 model and the 200
model.
and although programming these on the air is SO much fun?
I would rather do this per pc control.
but there is something called the CI200 which apparently is a
interface between the controller and the pc. But CAT went out business
and I have NEVER seen one of these devices. Is there a way to build
something to accomplish the same task to use the pc or just suck it up
and program over the air.





--
Untitled Document













--
Untitled Document

1 - 5 з 5