Thank you... 73 de -- Chris AD2CS *GCARC Education Committee Chair* *GCARC Membership Committee Chair* *Member, GCARC Board of

Thank you, I've boxed the stuff up in a Priority Flat Rate box, including the construction manuals for both the LF and HF versions of the kit.  Note:  The extra toroid cores I ordered are in one of

Never mind. Looks like someone else came. From his iPhone : Guy Mengel eastroad.org@groups.io> wrote: -- guy (at) eastroad (dot) org -.-. --.- -.-. --.- -.. . \|%|/// | ~ ~ | ^( @ @

The problem with the 24 bit ADCs out there is that they have a 24 bit output format, but don’t actually give 24 noise free bits. The AK5394A, for me in my use case could give 20.6 bits (192khz) and

Phillip -- I will mail the PMO on Monday afternoon or Tuesday morning depending upon when I can get to the Post Office. Thank you... 73 de -- Chris AD2CS *GCARC Education Committee Chair* *GCARC

Hi Chris, OK, it's all yours for 135 shipped.  Please give me a good shipping address and I'll box it all up.  It is far better to sell it now rather than put the burden of it on my niece when I'm

Phillip. Good morning. I will make them for you gratis for you to use. We have spoken before. I will be glad to help. If not then I will buy the from you a use them myself for ndb and listening

Dave, I was thinking of modern SDRs recently. It you can make do with a small frequency range then it could be said modern ones have only just caught up with Softrocks:-) A fair quality mid range

<Phillip Atchley> If the kits offered for $135 via a PMO are still available and unclaimed, I would like to buy them from you. Please respond with availability... 73 de -- Chris AD2CS *GCARC

Guy, So there was a global semiconductor shortage a few years ago, around the time Tony quit, and the Si570 and the audio op-amps were basically unobtainable. I needed a few of the Lite II

I also still have some unbuilt softrock kits including at least one case. If anyone is interested, let me know and I will get them out and post what I have exactly. 73, Tim

Hi Guy (My Uncle on my mother's side was named "Guy", Hey a year or so ago I bought TWO of the Softrock Ensemble II receiver kits from Ben Cherry AD8AW for $79 each.  I've long been a Softrock fan

Hi All; I have been working at home on the many softrocks I have obtained for a very reasonable price. Some still new from Tony in 2022. I was shocked to see the costs of softrock RXTX kits go up

OOPS! I used 100 mils as the pin spacing of the SOIC chip. Too many years with DIP chips. Probably exactly a factor of 2 too big. Sorry David K0IMH

Sorry, I do not have a crystal. However, the later model Eagles have an amplifier just in front of the crystal filter. There's a TMP connector on the board! You will see filter "suck out" at the

Christopher, I used the picture off the back of the board from stage 3 of the assembly instructions( divider) Scaling from the chip pad spacing with 8 pads I get board width 2.99 inch in the

Hello Christopher, Sorry, check the link at the end. That goes to the original home page that has the complete build notes. I kind of botched that post. Sorry Chuck

Hello Christopher, Did you check this page?? WB5RVZ Softrock Software Defined Radio Homepage (www.wb5rvz.com) ( http://www.wb5rvz.com/sdr/ ) wb5rvz.com ( http://www.wb5rvz.com/sdr/ ) (

Thanks -- I have another set of board photos, and that is exactly what I figured that I would have to do, but I was just hoping that there was an easier way.. LOL 73 de -- Chris AD2CS *GCARC

The photos on this page <https://www.wb5rvz.com/sdr/New_SR_Lite/02_lo.htm> aren't enough? You'd have to extrapolate dimensions from IC inter-pin spacing, but they all appear to be the same and there