We are new Aliner owners and have a 2023 Aliner Evolution that has an external mount for an outside two burner propane stove and a propane hookup for this stove. Does Aliner make their own propane stove? We have not been able to find any information! Any input appreciated!

We have been looking to find a way to transport our two e-bikes that weigh 77 pounds each while we are pulling our Aliner Family Expedition. Does anyone have any suggestions? Thanks, Nate and Karon

I used compressed air to blow out the spider webs from both of the condensate drains. Now all but maybe a couple of drops comes out of the driver side drain. I believe that the drain area was somewhat blocked and causing the water to reach the other drain and spill out of the box. I emailed Aliner and asked about removing the unit cover to properly clean the inside and they said I “might” be able to remove the cover with the unit still installed in the camper but didn’t recommend that I do. When the a/c season is about done I my try to get in there but I don’t want to do something stupid while we still need it. JoeS

Twice we have found water under the rug (rubber backed heavy duty entry carpet) in front of where the a/c vents are when the a/c has been going for a while. Could this be condensation? What can we do about it? Insulate the floor? All the cupboards around this area are dry. JoeS

2022 Aliner Ranger 10 dual bunk model. I noticed daylight between the two pieces of the roof where they meet at the peak. The sidewalls raise up and lock in without malfunction - no scraping, no gapping as far as I can see, they just fit into place fine. But from about 3-4 inches in from each peak corner, there's an apparent curvature to the peak edges of one or the other or both roof pieces. What causes this and how can I correct it? The weather stripping appears undamaged, and the "daylight" that's visible appears filtered through something white/pale, which I assume is some kind of overhang/rain shield? But I'm concerned the peak edge is no longer watertight. Thanks!

It was hot enough that I actually thought it was incandescent - until I took off the cover and discovered it was an LED plate. The light I'm talking about is the amber oval outside the door to the lower left. It has a rocker switch on the underside. Should I be concerned that there's too much resistance and it's a fire hazard, or what can I do to ensure it's not having some kind of issue? Thanks!

I want to change out my incandescent bulbs to LED's in my clearance and porch lights, and I suppose the tail lights. Those are not the C194's. I know it's been done, but not sure if there is anything I should, or should not get. There are plenty of options on Amazon. Thanks -- Don DeRyke Sunrise, Florida 2009 Classic, 2020 Ford Escape, 2.0 liter EcoBoost, AWD. Previous TV 2015 Ford Escape 1.6 ltr EcoBoost engine.

After being away from home for a few days (not camping), I came back and noticed an electrical cable hanging down from our 2012 Aliner Classic. When I went outside I saw knaw marks on the cable, meaning probably squirrels sharpening their teeth. My local car mechanic also has worked on electical problems with my Aliner and other RVS and has an Airstream for camping. I told the car mechanic that I would buy the replacement cable and just wondering where to purchase it, locally, or by mail order (I live 40 miles west of Detroit)? On the "chewed" cable it is stamped "14/2 SAE 19/27 D23 PVC 60C Jacketed Brake Cable". Any help would be appreciated. Thanks in advance! Bob Krzewinski - Ypsilanti MI

Hi all, several members have mentioned that Susan Orgeron makes covers for Aliner air conditioners that stick out on the side. Mine is a 2014 Aliner Ranger 12, but it no longer has the stock AC unit, but a slightly bigger LG 6k btu unit. Can anyone please put me in touch with Susan? Can't figure out a way to search members on here or directly message her. I'd like to get it covered before we leave on a long road trip on July 19th. Thank you!!

Has anyone installed a rear view camera? If so, how difficult is it to hardwire it to provide power? Where do you put the monitor? Can it be fastened to the rear view mirror - that would be a great place since the mirror is not useful when towing. Thanks, Don Knabb

Does anyone have experience with the above within our a-frame camper universe? If ‘yes’ - was it resolved, panels replaced or was the entire trailer was written-off? There’s a plethora of ‘roof leakage’ issues reported but none (that I was able to find) on whole roof panel waterlogging. A bud’s Jayco a-frame trailer has definitely experienced waterlogged roof panels. Roof panels were getting increasingly heavier. Friend was NOT getting any weaker! Replaced all 4 torsion rod corner lift assists. No change. An RV repair shop cited ‘waterlogged roof panels’ and corrected another customer’s identical issue by leaving panels upright for two weeks, drilling strategic drain holes and running ventilation fans to dry out the moisture. Problem resolved apparently. Got me wondering if: 1.) This forum’s frequent reports of ‘inability to lift roof panels’ could be caused (at least in part) by roof panel waterlogging (in addition to elderly weakening bodies?); and if …… 2.) Waterlogged roof panels are endemic to ALL fixed flat roofed trailers without owners’ knowledge unless owners are regularly weighing their rigs with identical content weight each time (very unlikely!). Jeff G. Whose 2002 Chalet Arrowhead trailer is (fortunately) garage stored.

We've tried using the water heater in our brand new Expedition, but it doesn't seem to ever produce hot water. we have gas appliances otherwise working and the switch is of course turned on. What are we missing? Haven't called the dealer yet.

As mentioned in previous post, I'm going to grease my wheel bearings (2016 Ranger 15 with EZ Lube fittings). - Assuming best to do with roof down of course. - Do I raise the stabilizers and remove BAL tire leveller so camper is just resting on two wheels and jockey wheel? - Then jack up one wheel (chock the other), keeping jockey wheel as is? Grease bearings and repeat for other side...